15
May
Carburetor Rebuild Kit Selector. How To Install A Holley Carburetor.
How To Diagnose Common Engine Problems With A Vacuum Gauge.
Holley carburetor installation instructions. Install the carburetor-mounting studs in the proper location on the intake manifold carburetor flange. Place the new carburetor flange gasket provided with the carburetor in the proper position on the intake manifold. Place the carburetor on top of the flange gasket on the manifold.
The new carburetor installation. This is performed by disconnecting the fuel line at the pump and blowing the line clean with compressed air. Holley DOES NOT recommend the procedure where the coil wire is disconnected the engine is cranked for a few revolutions and the fuel is collected in a container.
Install the carburetor-mounting studs not provided in the proper location on the intake manifold carburetor flange. Place the new carburetor flange gasket provided with the carburetor in the proper position on the intake manifold. Place the carburetor on top of the flange gasket on the manifold.
Carburetor Installation And Tuning Articles. High Performance Tuning Instructions. How To Diagnose Common Engine Problems With A Vacuum Gauge.
Holley carburetors have powered every NASCAR Cup team and nearly every NHRA ProStock champion for four decades. Install the carburetor-mounting studs not provided in the proper location on the intake manifold carburetor flange. Place the new carburetor flange gasket provided with the carburetor in the proper position on the intake manifold.
Place the carburetor on top of the flange gasket on the manifold. To install the new Holley carburetor the following procedure is suggested prior to assembly on the manifold. Assemble to the Holley throttle lever in the appropriate locations this can be determined by comparison with the original carburetor any balls or lever extensions that were used on the original carburetor.
The carburetor should be installed directly onto its manifold without an adapter whenever possible. Sometimes an adapter can create problems with hood clearance airflow throttle linkage fuel line attachment andor fuel mixture distribution. Place the carburetor in position over the four stud bolts and secure in place.
Use the shortest wire from the kit and connect the bayonet end to the negative choke cap terminal marked -. Ground the eyelet end to the carburetor. Do this either under a screw on the vacuum secondary diaphragm cover or under a screw securing the choke housing to the main body as shown in Figure 10.
Needed Holley PN 20-2 or 20-38. Install the carburetor-mounting studs not provided in the proper location on the intake manifold carburetor flange. Place the new carburetor flange gasket provided with the carburetor in the proper position on the intake manifold.
If your carburetor is a 4150 or 4500 removal of the fuel bowl and metering block is identical to the steps you used during the primary-side service. If your carb is a 4160 you may have an external fuel transfer tube on the drivers side. With the primary fuel bowl removed you can simply pull the tube out of the secondary fuel bowl.
Install the carburetor-mounting studs not provided in the proper location on the intake manifold carburetor flange. Place the new carburetor flange gasket provided with the carburetor in the proper position on the intake manifold. High Performance Tuning Instructions.
Overview Of The Holley 4150 Vacuum Secondary Carburetor. How To Install A Holley Carburetor. Holley carburetors have powered every NASCAR Cup team and nearly every NHRA ProStock champion for four decades.
The mechanical secondary carburetor is best on a lighter car with radical camshaft and a lower gear and manual transmission or on a car that is going to be used for racing purposes. Here are some additional resources for you to see on Holley TV. How to properly set the Ford transmission kickdown lever when using a Holley four-barrel carburetor.
View and Download Holley 4160 installation instructions online. CONVERSION KIT less metering jets. 4160 pdf manual download.
This model of carburetor has the square bore flange bolt pattern. It can replace Holley Edelbrock Carter AFB and Autolite style carburetors with 5 316 x 5 58 bolt pattern. If you have a spreadbore style intake manifold you will need an adapter to install this carburetor.
Similar to the Mr. Carburetor Installation And Tuning. Videos and Blog Articles.
The Holley technical resource library. Carburetor Rebuild Kit Selector. If you have questions about our products need a part recommendation or just cant seem to find what you need you can contact our Tech Support online and receive answers.